✨CNY NOTICE✨

• Online purchases from our E-commerce stores will remain open 24/7. However, order processing will commence from 19th February 2024 onwards
• Read more: here

Technical Highlights

• Proprietary R2R + DSD Architecture
• True balanced 26BIT R2R + 6BIT DSD (32 steps FIR Filters)
• Matched Precision Thin Film 0.005% R-2R Network Arrays           
• Encapsulated Flagship Ultra Low Noise Power Supply
• High Purity Gold+Silver+Copper Alloy AC Transformers
• Oven Controlled Crystals OCXO
• Adaptive FIFO Buffer Reclocking
• Direct Digital Signal Processing FPGA
• DSD1024, PCM1536 Supports On USB & I²S Input
• Proprietary USB Audio Solution via STM32F446 Advanced AMR Based MCU
• Licensed Thesycon USB Driver For Windows Platform
• Driverless On Mac & Linux
• Dual AES/EBU Input Supports
• Sharp/Slow Filters Option
• I²S Pinout Configuration
• I²S DSD Channel Swap Configuration
• Upgraded 12th Anniv. Firmware

DSD  

• DSD64 (DoP) on Coax/AES/Opt Input
• DSD1024* On USB & I²S Input Only

PCM  

• 24bits / 44.1, 48, 88.2, 96, 176.4, 192KHz On All Input
• 1536kHz* On USB & I²S Input 

Sampling Mode: Non-Oversampling NOS / Oversampling OS

Digital Input  

• Coax via RCA
• TOSLink x 1
• AES/EBU x 2
• USB2.0 Type B
• I²S via HDMI LVDS
• I²S via RJ45 LVDS
• I²S via RJ45 LVCMOS

Analog Output          

• RCA at 2.0Vrms, 625 Ω
• XLR at 4.0Vrms, 1250 Ω

Clock Output BNC 75Ω

• 44.1KHz, 48KHz
• 22.5774Mhz, 24.576Mhz
• 45.1548MHz, 49.152Mhz

Frequency Response: 20-40KHz -0.2dB

THD: 0.08%(RCA), 0.004%(XLR)

S/N Ratio: 105dB(RCA), 115dB(XLR)

Dynamic Range: >132dB

Stereo Crosstalk: -110dB

AC Power Requirement: 100-240VAC, 50/60Hz (Worldwide Voltage)

Power Consumption: ≤20W

Dimension: 430W x 380D x 125H mm (Includes Footers)

Package Dim: 610 x 570 x 275 mm

Package Content: DAC only. No power cord & remote control.

Weight: 19.0 Kg           

Color: Silver / Black

Warranty: 36 Months

DENAFRIPS Support Page

Improvements of the Terminator II over the older Terminator:

• Total segregation of Digital Signal Processing and R-2R Network Arrays (Analog) boards
• Oven-Controlled Crystal Oscillators OCXO replace the TCXO clocks.
• High-speed Digital Isolation. The silicon-dioxide (SiO2 ) isolation barrier with isolated power supply effective isolate the ground and block the noise from one end to the other
• Redesigned Power Supply Unit (encapsulated underneath the DAC board)
• Supercapacitors for Digital & Analogue circuitry for high energy storage to ensure supply of constant cleaned DC power to the circuitry
• Clock Out eco-system to sync with DENAFRIPS DDC.

Now you ask, what are the differences between the Terminator II and the Terminator Plus?

The differences between the Terminator II and Plus, the Terminator Plus comes with premium offering of:

• Aluminum anodized curvy front panel
• Precision, hand-picked, premium OCXO
• Hand-picked R-2R board

I²S

I²S has no industry standard. If you would like to use the I²S connection, the I²S pinout matching with the source (DDC/Transport/Streamer) has to be configured correctly. Mismatch of I²S pinout may result in static/noise output. The excessive noise output level may damage the loudspeakers/headphone drivers.

Suggestion of I²S matching with the source, i.e. DDC/Transport/Streamer
​
1. Connect the I²S cable (good quality HDMI cable <3ft/1m)
2. Turn down the volume (audible, minimal)
3. Play a familiar music (PCM first, followed by DSD)
4. Run through the I²S setting of the DAC, 000-111
5. One of the modes should match with the source for both PCM and DSD playback.
​
It's recommended to go through the Audio Tone Test to make sure the L/R channel, in phase/out of phase correctness.

Warning
Please note that the RJ45/HDMI ports of DENAFRIPS DAC are not typical network/multimedia RJ45/HDMI ports. They are purpose-built I²S ports. Please do not connect it to the typical multimedia HDMI port (i.e. Bluray player/TV etc) / Ethernet network.

Need help?
Please reach out to us at support@vinshineaudio.com . We are happy to assist you.

VAT Prepaid (DDP) Shipping Option

We offer Delivered Duty Paid (DDP) shipping option for customers who reside in the EU/UK. To you, as a customers who live in the EU, it is as if the product is shipped within the EU after the package is cleared from the customs. The courier crew will deliver the package to your doorstep, you do not need to pay additional charges on top of what you have paid when placing the order.

The typical timeline of DDP shipment is as follows:

• Package hand over to the shipping company on the day you receive the tracking information
• Shipping company export the package to the EU
• Once the package arrived in the EU, i.e. Liege Airport, customs clearance process begin
• Once the customs clearance is completed, local courier (i.e. DPD/DHL) will pick up the package for delivery
• The package will be delivered within the EU to your doorstep

The shipment takes about 18-20days to complete.

Read more: link here